How to root Samsung Galaxy S6 edge+

Galaxy S6 edge+ Preview

Galaxy S6 edge+ Specs and full info

Prerequestis :
-Be for doing anything you have to backup your Data See this guide here
-Charge your phone more than80% .

Step by step root for Samsung Galaxy S6 edge+ :

§ Stock Auto-root kernel for Galaxy S6 Edge+

§ Model no. SM-G928F — Link

§ Model no. SM-G92oi — Link

§ Model no. SM-G928C — Link

§ Model no. SM-G928S — Link

§ Model no. SM-G928K — Link

§ Model no. SM-G928L — Link

§ Model no. SM-G928T — Link

§ Model no. SM-G928W8 — Link (alternative: another kernel)

§ Model no. SM-G928P – Link

§ Model no. SM-G928A – not available

§ Model no. SM-G928V – not available

§ Model no. SM-G928R4 – not available

§ Odin PC software — Link | File: Odin-3-10-7.zip (1.03 MB)

1. Download Odin and Stock Auto Root kernel file from above.

2. Install Galaxy S6Edge+ driver (method 1 there!) first of all. Double click the .exe file of drivers to begin installation. (Not required if you have already done this.)

3. Extract the Odin file. You should get this file, Odin3 v3.10.7.exe (other files could be hidden, hence not visible).

4. Disconnect your Galaxy S6 Edge+ from PC if it is connected.

5. Enable OEM unlock on your device.

1. Go to Settings > About device. And then tap on build no. 7 times or until your get the message ‘You’re now a developer’.

2. Go back to Settings, scroll down, and tap on ‘Developer options’.

3. Look for ‘Enable OEM unlock’ and use its toggle to enable it. Accept the warning by tapping on OK button.

— Also make sure you have disabled the Find My Mobile option completely in Settings > Lockscreen and security settings.

6. Boot Galaxy S6 Edge+ into download mode:

1. Power off your Galaxy S6 Edge+. Wait 6-7 seconds after screen goes off.

2. Press and hold the three buttons Power + Home + Volume down together until you see warning screen.

3. Press Volume Up to continue to download mode.

7. Double click on extracted file of Odin, Odin3 v3.10.7.exe, to open the Odin window, as shown below. Be careful with Odin, and do just as said to prevent problems.

8. Connect your Galaxy S6 Edge+ to PC now using USB cable. Odin should recognize your Galaxy S6 Edge+. It’s a must. When it recognizes, you will see Added!! message appearing in the Log box in bottom left, and the first box under ID:COM will also show a no. and turn its background blue. Look at the pic below.

§ You cannot proceed until you get the Added!! message, which confirms that Odin has recognized your device.

§ If you don’t get Added!! message, you need to install/re-install drivers again, and use the original cable that came with the device. Mostly, drivers are the problem (look at 2 above).

§ You can try different USB ports on your PC too, btw.

9. Load the stock auto root kernel file into Odin. For this, click the AP button on Odin and the select the kernel file in .tar format.

Downloads

Download stock Auto Root kernel for your device’s model no. from below, and then follow the guide to install it on your device.

10. Make sure Re-partition checkbox is NOT selected, under the Options tab. Don’t use PIT tab either. Go back to Log tab btw, it will show the progress when you hit start button in next .

11. Click the Start button on Odin now to start flashing the firmware on your Galaxy S6 Edge+. Wait till installation is finished, after which your Galaxy S6 Edge+ will reboot automatically. You’ll get PASS message as show below upon successful installation from Odin.

§ If Odin gets stuck at setup connection, then you need to do this all again. Disconnect your device, close Odin, boot device into download mode again, open Odin, and then select the firmware and flash it again as said above.

§ If you get FAIL in the top left box, then also you need to flash the firmware again as stated just above.

12. Install the SuperSU app from the play store. Open it, and you will have root access.

That’s it. Enjoy the Root access on your Galaxy S6 Edge+!

Check the root with root checker here

Source : AndroidSoul,GsmArena